🎨 Touch Up Paint

1. 🧼 Clean the Area: Use alcohol wipes or cleaner. Let dry completely.
2. Lightly Sand (Optional): Smooth out rust or rough spots. Wipe clean.
3. 🔄 Shake Well: Shake the paint bottle or pen for 2 minutes.
4. 🖌️ Apply Paint: Use brush or tip. Let dry 10–15 minutes between coats.
5. ✨ Optional Finish: After a few days, wet sand and polish if needed.
6. Always do a test Area to insure correct colour before Application.
7. BE SAFE : Refer to Our PPE Information at the bottom of this page

🎨 Touch Up Paint (2-Stage)

• 🖌️ Apply the ground coat first. Let dry for 2 hours.
• Then apply the finish coat in light layers, letting it dry between coats.
• BE SAFE : Refer to Our PPE Information at the bottom of this page

🛠️ Touch-Up Paint Repair Kit

1. 🧼 Preparation: Clean with compound and alcohol wipes. Sand if necessary.
2. 🖌️ ✅ Primer: Apply if needed. Light coats with 15 minutes dry time. Full dry 2 hours.
3. 🔄 Paint: Shake well. Apply light coats. 10–15 mins between coats. Dry overnight.
4. ✨ Finish: Sand lightly and polish using SP5000 compound for best blending.
5. ⚠️ ✅ Tips: Avoid washing for 48 hrs. Use in warm, dry area. Store kit in the box.
6. BE SAFE: Refer to Our PPE Information at the bottom of this page

✨ Direct Gloss Aerosol

• 🎯 Spray in ventilated area. Wear a mask.
• BE SAFE: Refer to our PPE Information at the bottom of this page
• 🔄 Shake for 3 minutes before use.
• 🎯 Spray 6–8 inches from surface. Light coats. Wait 10 mins between coats.
• Dry with air movement or hair dryer from 14” away.
• ❌ No Lacquer Needed: This is a direct gloss. Do not apply clear coat.
• ✅ Primer may be required on bare or unpainted surfaces.
• Never heat the Aerosol
• Always do a test Area to insure correct colour before Application.

🌈 Basecoat Aerosol + Lacquer

• 🧼 Clean and sand surface. Mask off nearby areas.
• 🔄 Shake basecoat and spray light coats 10 mins apart.
• After 20–30 mins, apply 3 clear lacquer coats 10–15 mins apart.
• ✨ Allow 24–48 hours to cure. Polish if needed.
• ✅ Primer may be needed on bare or porous surfaces.
• Never heat the aerosol
• Always do a test Area to insure correct colour before Application.
• BE SAFE: Refer to Our PPE Information at the bottom of this page

🔥 Heat Resistant Brush-On

• 🧼 Clean and degrease. Sand rough areas smooth.
• 🖌️ Apply with brush in light, even coats. 15 mins between coats.
• Let cure for 12 hours before exposing to heat.
• BE SAFE : Refer to Our PPE Information at the bottom of this page

🔥 Heat Resistant Aerosol

• 🎯 Spray in ventilated area. Clean surface. Sand if needed.
• 🔄 Shake can 2–3 minutes. Spray light coats 15 mins apart.
• Dry for 12 hours before heat exposure.
• ✅ Primer may be needed depending on surface.
• BE SAFE : Refer to Our PPE Information at the bottom of this page

🛋️ Leather Water-Based Paint

• 🧼 Clean leather thoroughly. Let dry.
• 🖌️ Apply light coats using sponge or spray. 20 mins between coats.
• 💨 Air dry or use hair dryer. Full cure: 24 hours.
• ⚠️ Ideal temp: 15–25°C. Avoid thick layers.

🧪 Chlorinated Rubber Paint

• Surface must be clean, dry, and free from rust, grease or loose paint.
• 🖌️ Apply in dry conditions. Do not apply in high humidity or before rain.
• 🥄 Can be brushed, rolled or sprayed. Stir well before use.
• 🕒 Apply 1–2 coats. Wait 6–8 hours between coats. Full cure 24 hours.
• ⚠️ Use in well-ventilated areas. Avoid thick coats.
• BE SAFE : Refer to Our PPE Information at the bottom of this page

🖌️ PVC Acrylic Paint (Brush-On)

• 🧼 Clean with isopropyl alcohol. Remove wax and grease.
• ✅ Suitable for PVC, ABS and most plastics. Primer rarely needed.
• ⏱️ Stir thoroughly. Apply thin, even coats with brush. Recoat after 1–2 hours.
• 🕒 Touch dry in 20–30 minutes. Full cure in 24 hours.
• 🧼 Clean tools with thinners.
• BE SAFE: Refer to Our PPE Information at the bottom of this page

🧴 PVC Acrylic Paint (Aerosol)

• 🧼 Clean surface thoroughly. Scuff with fine pad if very smooth.
• 🔄 Shake for 2–3 minutes. Apply light coats 10–15 mins apart.
• 🕒 Touch dry in 30 mins. Fully cured in 24–48 hours.
• 🎯 Spray upside down for 6 seconds after use to clear nozzle.
• NEVER HEAT THE AEROSOL
• BE SAFE: Refer to Our PPE Information at the bottom of this page

🏭 Industrial Enamel Paint

• 🧼 Clean and dry the surface. Remove rust or old flaking paint.
• Use on metal, wood, machinery, tools, railings, furniture.
• 🎯 Brush-on: Thin even coats. Aerosol: Spray 6–8” away. Wait 10 mins between coats.
• 🕒 Touch dry 15–30 mins. Recoat after 10 mins. Full dry in 24 hours.
• BE SAFE : Refer to Our PPE Information at the bottom of this page

🪑 Water-Based Furniture Paint

• 🧼 Clean the Surface: Wipe with degreaser or mild soapy water. Rinse and let dry completely.
• 🪵 Sand Lightly: Use fine-grit sandpaper (320+), especially on glossy or previously coated surfaces. Remove dust.
• 🔄 Stir Well: Mix the paint thoroughly. Avoid shaking to prevent bubbles.
• 🖌️ Apply Thin Coats: Use a good brush, roller or spray. Light, even coats work best.
• ⏱️ Dry Time: Touch dry in 30–45 mins. Recoat after 2 hours. Full cure in 24–48 hrs.
• ⚠️ Tips: Ideal temp 15–25°C. Don’t apply thick coats. Optionally seal with a water-based clear coat for durability.