Instructions for Use
Scooby's Paint โ Product Instructions
Select your product below to view instructions:
- ๐จ Touch Up Paint
- ๐จ Touch Up Paint (2-Stage)
- ๐ ๏ธ Touch-Up Paint Repair Kit
- โจ Direct Gloss Aerosol
- ๐ Basecoat Aerosol + Lacquer
- ๐ฅ Heat Resistant Brush-On
- ๐ฅ Heat Resistant Aerosol
- ๐๏ธ Leather Water-Based Paint
- ๐งช Chlorinated Rubber Paint
- ๐๏ธ PVC Acrylic Paint (Brush-On)
- ๐งด PVC Acrylic Paint (Aerosol)
- ๐ญ Industrial Enamel Paint
๐จ Touch Up Paint
- ๐งผ Clean the Area: Use alcohol wipes or cleaner. Let dry completely.
- Lightly Sand (Optional): Smooth out rust or rough spots. Wipe clean.
- ๐ Shake Well: Shake the paint bottle or pen for 2 minutes.
- ๐๏ธ Apply Paint: Use brush or tip. Let dry 10โ15 minutes between coats.
- โจ Optional Finish: After a few days, wet sand and polish if needed.
๐จ Touch Up Paint (2-Stage)
- ๐๏ธ Apply the ground coat first. Let dry for 2 hours.
- Then apply the finish coat in light layers, letting it dry between coats.
๐ ๏ธ Touch-Up Paint Repair Kit
- ๐งผ Preparation: Clean with compound and alcohol wipes. Sand if necessary.
- ๐๏ธ โ Primer: Apply if needed. Light coats with 15 minutes dry time. Full dry 2 hours.
- ๐ Paint: Shake well. Apply light coats. 10โ15 mins between coats. Dry overnight.
- โจ Finish: Sand lightly and polish using SP5000 compound for best blending.
- โ ๏ธ โ Tips: Avoid washing for 48 hrs. Use in warm, dry area. Store kit in the box.
โจ Direct Gloss Aerosol
- ๐ฏ Spray in ventilated area. Wear a mask.
- ๐ Shake for 3 minutes before use.
- ๐ฏ Spray 6โ8 inches from surface. Light coats. Wait 10 mins between coats.
- Dry with air movement or hair dryer from 14โ away.
- โ No Lacquer Needed: This is a direct gloss. Do not apply clear coat.
- โ Primer may be required on bare or unpainted surfaces.
๐ Basecoat Aerosol + Lacquer
- ๐งผ Clean and sand surface. Mask off nearby areas.
- ๐ Shake basecoat and spray light coats 10 mins apart.
- After 20โ30 mins, apply 3 clear lacquer coats 10โ15 mins apart.
- โจ Allow 24โ48 hours to cure. Polish if needed.
- โ Primer may be needed on bare or porous surfaces.
๐ฅ Heat Resistant Brush-On
- ๐งผ Clean and degrease. Sand rough areas smooth.
- ๐๏ธ Apply with brush in light, even coats. 15 mins between coats.
- Let cure for 12 hours before exposing to heat.
๐ฅ Heat Resistant Aerosol
- ๐ฏ Spray in ventilated area. Clean surface. Sand if needed.
- ๐ Shake can 2โ3 minutes. Spray light coats 15 mins apart.
- Dry for 12 hours before heat exposure.
- โ Primer may be needed depending on surface.
๐๏ธ Leather Water-Based Paint
- ๐งผ Clean leather thoroughly. Let dry.
- ๐๏ธ Apply light coats using sponge or spray. 20 mins between coats.
- ๐จ Air dry or use hair dryer. Full cure: 24 hours.
- โ ๏ธ Ideal temp: 15โ25ยฐC. Avoid thick layers.
๐งช Chlorinated Rubber Paint
- Surface must be clean, dry, and free from rust, grease or loose paint.
- ๐๏ธ Apply in dry conditions. Do not apply in high humidity or before rain.
- ๐ฅ Can be brushed, rolled or sprayed. Stir well before use.
- ๐ Apply 1โ2 coats. Wait 6โ8 hours between coats. Full cure 24 hours.
- โ ๏ธ Use in well-ventilated areas. Avoid thick coats.
๐๏ธ PVC Acrylic Paint (Brush-On)
- ๐งผ Clean with isopropyl alcohol. Remove wax and grease.
- โ Suitable for PVC, ABS and most plastics. Primer rarely needed.
- โฑ๏ธ Stir thoroughly. Apply thin, even coats with brush. Recoat after 1โ2 hours.
- ๐ Touch dry in 20โ30 minutes. Full cure in 24 hours.
- ๐งผ Clean tools with thinners.
๐งด PVC Acrylic Paint (Aerosol)
- ๐งผ Clean surface thoroughly. Scuff with fine pad if very smooth.
- ๐ Shake for 2โ3 minutes. Apply light coats 10โ15 mins apart.
- ๐ Touch dry in 30 mins. Fully cured in 24โ48 hours.
- ๐ฏ Spray upside down for 6 seconds after use to clear nozzle.
๐ญ Industrial Enamel Paint
- ๐งผ Clean and dry the surface. Remove rust or old flaking paint.
- Use on metal, wood, machinery, tools, railings, furniture.
- ๐ฏ Brush-on: Thin even coats. Aerosol: Spray 6โ8โ away. Wait 10 mins between coats.
- ๐ Touch dry 15โ30 mins. Recoat after 10 mins. Full dry in 24 hours.